Click the image for technical data

Fully compliant with EN54 parts 2 & 4, the E100 Range of analogue addressable fire alarm panels offers high performance at a competitive price.

Attractively designed, easy to use and simple to install, the E100's improved specification now includes delay timers, phased evacuation facilities, adjustable contamination levels and the programming of non-fire events.

These new features, combined with the panel's comprehensive range of existing features and straightforward programming via the E100's intuitive upload/download programming software.

TECHNICAL SPECIFICATIONS
POWER SUPPLY SPECIFICATION
Mains supply voltage	230V a.c. ± 10% 50/60Hz
Internal power supply	27V d.c. Nominal
Total output current limited to	3A @ 230V a.c. (1.5A on economy panels) (27V norminal).
Max. battery size and type	7.0 Ahr VRLA
Quiescent current drain	< 80mA (1 loop unloaded); <100mA (2 loop unloaded)
LOOP DRIVER SPECIFICATION
Max. number of loop drivers allowed	2 (1 on economy panels)
Max. loop output current	350mA
Max. addressable devices per loop (XP95)	126
Max. loop sounders per loop	32
Number of programmable sounder groups	15
Number of programmable output sets	32
CONVENTIONAL SOUNDER CIRCUIT SPECIFICATION (FUSED AT 1A)
Number of programmable circuits	4
End of line resistor value	6800 ohms 5% Tol. 0.25 W
Line monitored for open and short circuit faults	YES
Max. number of bells @ 25mA	120
Max. number of sounders @ 20mA	150
AUXILIARY OPEN COLLECTOR OUTPUTS (MAX. SINK CURRENT 100mA EACH, 300mA TOTAL)
Max. open circuit voltage	27V d.c.
Reset output	Active during reset cycle
Remote output	Active during any fire condition (can be zonally delayed/isolated)
Pre-alarm output	Active during any pre-alarm condition
Fire 1	Active during any fire condition
Fire 2	Active during any fire condition (except silenced fire)
Fault	Active when no faults are present - failsafe to open circuit
24V aux. power output	1A fused
AUXILIARY INPUTS
Reset	Connect to 0V to trigger. Max. input voltage 27V d.c. (Non-latching)
Silence	Connect to 0V to trigger. Max. input voltage 27V d.c. (Non-latching)
Class change (Evacuate - continuous sounders)	Connect to 0V to trigger. Max. input voltage 27V d.c. (Non-latching)
Alert (Phased Evacuate - pulsed sounders)	Connect to 0V to trigger. Max. input voltage 27V d.c. (Non-latching)
PANEL INDICATORS AND CONTROLS
Control buttons	Silence, Reset and Evacuate.
Event scrolling and menu access buttons	Up (1); Down (2); Accept (3); Abort (4)
Liquid Crystal Display	Two lines x 40 characters, backlit
LED indicators	16 Zonal LEDs (expandable to 32); General Fire, System Energised; Pre-Alarm; Remote Output Activated; Menus Accessed; Disablement; Test; Remote Output Disabled; Silenced; General Fault; System Fault;
PHYSICAL DIMENSIONS
Approx. dimensions of back box (WxHxD)	410 x 250 x 80mm (metal)
Approx. dimensions of lid (WxHxD)	439 x 274 x 7mm (plastic); 435 x 270 x 5mm (metal);
Weight (without batteries)	4.5kg
CABLING REQUIREMENTS
Type of cable	Fire resistant screened cable, minimum size 1mm2
Max. cable length per loop	1 KM
Max. allowable loop impedance (each conductor)	20 ohms
Max. cable capacitance	0.27µF
REPEATER SPECIFICATION
Repeater connection	Via BF/A/711 Network Driver Card fitted to Main panel's RS485 port
Max. number of repeaters per system	15 not applicable
Max. cable length per repeater network	1 KM (daisy chain configuration) not applicable
PC/PRINTER INTERFACE
PC connection	Via main panel RS232 molex connector (lead supplied in BF/A/707 kit)
Printer connection	Via main panel RS232 connector block